16

Working with Link Configuration

• Overview of link configuration
• Viewing link statistics and metrics

Overview of link configuration

Link configuration is based on entries you make when you run the Setup utility. When you run the Setup utility, you add the members for the default gateway pool, the self IP addresses for the Link Controller, and the VLANs. These objects are the basic components for link configuration.

You configure the links that you want to load balance in the Configuration utility. When you initially add links, you configure the basic properties for the link. Once you have configured the basic properties, you can refine and enhance the link configuration with several advanced configuration options. This chapter explains how to configure the basic properties of a link, and also how to configure the advanced properties of a link.

Note

Defining the basic properties for a link

Before you can load balance inbound and outbound traffic on the Link Controller, you configure the basic links. The following procedure describes how to configure the basic properties of a link.

To configure the basic link properties using the Configuration utility

1. In the navigation pane, expand the Link Configuration item, and and then click Links.
   The Link List screen opens.
2. Click the Add button.
   The Link Configuration: Step 1 of 2 screen opens.
3. In the Link Name box, type a name for the link.
4. In the Self IP box, select a self IP address to associate with the link.
5. In the VLAN box, type the name of the VLAN associated with the self IP address you selected in the previous step.
6. Next to the Gateway IP box, click the Add button to select the gateway IP address to associate with the link.
7. If you want to limit the volume of inbound traffic, check the box next to Inbound Traffic Limit, and type a number that represents the maximum throughput rate (in kilobits per second) for the inbound traffic on the link. (Note that this is an optional setting.)
8. If you want to limit the volume of outbound traffic, check the box next to Outbound Traffic Limit, and type a number that represents the maximum throughput rate (in kilobits per second) for the outbound traffic on the link. (Note that this is an optional setting.)
9. If you want to limit the total volume of bidirectional traffic, check the box next to Total Traffic Limit, and type a number that represents the maximum throughput rate (in kilobits per second) for the sum of inbound and outbound traffic on the link. (Note that this is an optional setting.)
10. Click Next.
    The Link Configuration (Step 2 of 2) screen opens.
11. In the Monitor Name box, type a name for the health monitor for the link. Alternately, you can select a default monitor from the list. (Note that this is an optional setting. If you do not want to configure a monitor at this time, skip to step 13.)
12. In the Monitor Type box, select the type of monitor for the link.
13. Click Finish.
    The link and optional monitor are added to the configuration, and the Link List screen opens.

Note

Working with the advanced properties for a link

Once you have configured the basic link properties, you can configure several advanced properties for the link. The advanced properties include:

• Additional basic link properties
• Additional health monitor properties
• Link weighting and billing properties
• SNMP properties

Configuring additional basic link properties

Once you have configured the basic properties of a link, you can adjust those properties, and configure several advanced properties. This procedure describes how to configure additional link properties.

To configure additional link properties using the Configuration utility

1. In the navigation pane, expand the Link Configuration item, and then click Links.
   The Link List screen opens.
2. Click the name of the link that you want to modify.
   The Link Properties tab opens.
3. Make any changes that you want to the basic properties of the link. In addition to the properties that you defined when you first configured the link, you can add an ISP name, or redefine the link bandwidth limit settings. For details on the additional settings on this screen, click the Help button.
4. When you have completed the changes that you want to make, click Apply.

Configuring additional health monitor properties

You can configure a health monitor when you first configure a link, or you can configure a health monitor at a later time. You can also configure additional settings for an existing monitor.

To configure additional health monitor properties using the Configuration utility

1. In the navigation pane, expand the Link Configuration item, and then click Links.
   The Link List screen opens.
2. Click the name of the link that you want to modify.
   The Link Properties tab opens.
3. Click the Link Monitor tab.
   The Monitor screen opens.
4. On the Monitor screen, you can define a monitor if you did not define one when you first configured the link. You can also configure additional settings for an existing monitor, for example Timeout and Interval. For details on the additional settings on this screen, click the Help button.
5. When you have completed the changes that you want to make, click Apply.

Note

Configuring link weighting and billing properties

With the link weighting and billing properties, you can refine the link load balancing and statistics reporting for the links in your configuration. On the Link Weighting screen, you determine how the Link Controller manages and distributes traffic across the links, using the following settings.

• Duplex Billing
  If your ISP provider uses duplex billing, you can set the Duplex Billing option so that the statistics and billing report screens on the Link Controller accurately reflect the bandwidth usage for the link. Note that by default, the duplex billing setting is on.
• Price Weighting
  If you want the Link Controller to load balance traffic based on the cost of the bandwidth, then select the Use Price Weighting option. You can use this weighting option to avoid the costs associated with exceeding your prepaid bandwidth. You can also use this weighting option to direct traffic over the least expensive link first.
• Ratio Weighting
  If you want the Link Controller to load balance the total traffic to the controller based on a ratio, then select the Use Ratio Weighting option. When you have links of varying bandwidth sizes, you can use this weighting option to avoid oversaturating a smaller link with too much traffic.

You can use either the price weighting option or the ratio weighting option to load balance your link traffic for all of your links. You cannot use both options. Regardless of which weighting option you use, you must use the same weighting option for all links.

To configure link weighting and billing properties using the Configuration utility

1. In the navigation pane, expand the Link Configuration item, and then click Links.
   The Link List screen opens.
2. Click the name of the link that you want to modify.
   The Link Properties tab opens.
3. Click the Link Weighting tab.
   The Link Weighting screen opens.
4. Make any changes that you want for the link weighting and billing properties. For details on the settings on this screen, click the Help button.
5. When you have completed the changes that you want to make, click Applyv.

Configuring SNMP properties

If you want the Link Controller to report the metrics gathered directly from the gateway router for the link, you need to enable SNMP for the link. Use the following procedure to enable SNMP communications with the gateway router.

Note

To enable SNMP for the gateway router using the Configuration utility

1. In the navigation pane, expand the Link Configuration item, and then click Links.
   The Link List screen opens.
2. Click the name of the link that you want to modify.
   The Link Properties tab opens.
3. Click the Link SNMP tab.
   The SNMP screen opens.
4. Add the settings to enable SNMP communications for the router. For details on the settings on this screen, click the Help button.
5. When you have completed the changes that you want to make, click Apply.

Viewing link statistics and metrics

Using the Configuration utility, you can view current statistics about the following objects in the Link Controller configuration:

To view the Link Statistics screens

1. In the navigation pane, expand the Link Statistics item, and then click the statistics screen that you want to review.
2. For details on the information provided on each screen, click Help.