Updated Date: 03/09/2008
This release note documents the version 4.2.16 feature release of the WANJet® appliance. We recommend this release only for those customers who want the fixes and enhancements listed in Fixes in this release. For new customers, the software is preinstalled on the WANJet appliance. For existing customers, you can apply the software upgrade to version 3.1.1 and later. For information about installing the software upgrade, please refer to Upgrading the software.
Note: F5 now offers both feature releases and maintenance releases. For more information on our new release policies, please see New Versioning Schema for F5 Software Releases.
In addition to these release notes, the following user documentation is relevant to this release (depending on your platform).
You can find the product documentation and the solutions database on the AskF5 Technical Support web site.
The supported browsers for the Web UI are:
This release supports the following platforms:
If you are unsure which platform you have, click the About link from any screen in the WANJet appliance's Web UI.
The following instructions explain how to upgrade existing WANJet appliances running version 3.1.1 and later to version 4.2.16. To upgrade the WANJet appliance, complete these tasks:
Important: For the WANJet appliance to function properly, TCP ports 3703, 3702, 3701, 10000, and 10001 must all be open on a firewall. Any firewalls separating the WANJet appliances must have these ports open. If you are using Delayed Connection Acceptance, port 62473 must be able to accept traffic from the bridge IP address and any configured VLAN IP addresses. For specific information about configuring ports, refer to the WANJet Appliance Administrator Guide.
Important: Version 4.0 introduced a new licensing procedure. If you are upgrading from version 3.1.x, you must first obtain a Base Registration Key. Do not proceed with the upgrade until you have the Base Registration Key. If you did not receive an email with a Base Registration Key, contact F5 Networks Technical Support (and be sure to have the WANJet appliance serial number) before attempting to install the software upgrade.
Always back up your current configuration before installing the software upgrade.
You can perform a remote upgrade to version 4.2.16 from version 3.1.1 or 3.1.2. If you are upgrading remotely from version 3.1.1 or 3.1.2, you must complete the following tasks.
Note: You must activate the license before you can use the WANJet appliance to optimize traffic. You need to perform this procedure only once for each WANJet appliance.
Note: If automatic license activation does not work, you can use manual activation instead. On the WANJet License Details screen, next to Activation Method, select Manual and follow the directions on the screen.
Note: You need to perform this procedure only if you have not previously saved the chassis serial number in the About box.
Release 4.2.16 includes the following fixes.
VLAN support if WANJet appliances are in the same network (CR90960)
In previous releases, the WANJet appliance could not optimize traffic through VLANs if both WANJet appliances were in the same network. In this release, the WANJet appliance can optimize VLAN traffic even if the appliances are in the same network.
Delayed Connection Acceptance changes (CR92179)
The Delayed Connection Acceptance feature postpones acceptance of LAN requests for specified ports until the server connection is verified. In releases prior to 4.2.16, we recommended disabling delayed connection acceptance for one-arm configurations. In this release, you can use delayed connection acceptance for ports on any WANJet appliance in any configuration including one-arm. Note that as of this release if you are using Delayed Connection Acceptance in any configuration, port 62473 must be able to accept traffic from the bridge IP address and any configured VLAN IP addresses.
Autopass disabled by default (CR92215)
In previous releases, the Autopass feature was enabled by default. If the WANJet appliance attempted to make a connection to a server that did not respond, Autopass caused the WANJet appliance to wait 5 minutes before attempting to optimize traffic on that connection. In this release, Autopass is disabled by default. If you have slow or problematic services, you may want to add specific ports to the list of ports that will delay accepting requests until the server connection is verified. For troubleshooting this type of problem, you could shut off optimization for the services/ports having a problem. If the service fails right away, you should try using delayed connection acceptance for that port.
[ Top ]
The following items are known issues in the current release.
TDR-2 efficiency on WANJet 200
On WANJet 200 appliances, the overall cache size for data transmitted or received is 50 MB, or 25 MB in each direction. TDR-2 efficiency may be degraded when transmitting or receiving application data sets of 25 MB or greater.
Passthrough sessions (CR60178)
After a high volume of traffic passes through the WANJet appliance, the dashboard may temporarily display more passthrough sessions than are actually occurring.
SSL encryption implementation (CR64020)
SSL encryption is currently implemented only for optimized TCP traffic. In future releases, we plan to support TCP and UDP protocols for SSL encryption.
TDR-2 efficiency impacted by slow servers (CR65171)
TDR-2 efficiency may be degraded when transmitting data from low-performance servers.
UDP port optimization may cause problems on port 53 (CR70172)
When all UDP ports are optimized, DNS services over port 53 may fail. The workaround is to put all UDP ports into passthrough mode, and to specifically open those UDP ports you want to optimize.
Delayed Acceptance setting enabled after upgrade (CR81526)
The Delayed Acceptance setting is set to its default value of Enabled after you upgrade the WANJet appliance to a newer release, regardless of what it was set to in the previous release. If you do not want to enable delayed connection acceptance, after upgrading, click Settings for Delayed Connection Acceptance on the Local WANJet appliance screen, and clear the Enable box.
[ Top ]
For additional information, please visit http://www.f5.com.